Shark Carpet Cleaner S3250CW User Manual

LIGHT & EASYSTEAM MOP  
S3250CW  
OWNER’S GUIDE  
WWW.SHARKCLEAN.COM  
 
S3250CW_11_IB_ENG_100913.indd  
1
10-09-13 10:57 AM  
corners. Keep power cord  
away from heated surfaces.  
21. Extreme caution should be  
exercised when using this  
appliance to clean stairs.  
IMPORTANT SAFETY INSTRUCTIONS  
SAVE THESE INSTRUCTIONS  
For Household Use Only  
11. DO NOT unplug by pulling on  
power cord. To unplug, grasp  
the plug not the power cord.  
Do not use extension cords or  
outlets with inadequate current  
carrying capacity.  
22.Never use steam mop without  
micro-fiber pad attached.  
23.Keep your work area well lit.  
1. Use the system only for its  
WHEN USING YOUR SHARK®  
24.Store steam mop indoors in a  
cool, dry place.  
intended use.  
STEAM MOP, BASIC SAFETY  
12. DO NOT put any objects into  
openings. Do not use with any  
opening blocked.  
2. DO NOT use outdoors.  
PRECAUTIONS SHOULD ALWAYS  
25.To avoid circuit overload, do  
not operate another appliance  
on the same socket (circuit) as  
the steam cleaner.  
3. DO NOT leave the appliance  
BE FOLLOWED, INCLUDING THE  
unattended when plugged in.  
13. DO NOT put hands or feet  
under the steam mop. Unit  
gets very hot.  
FOLLOWING:  
Always unplug the power cord  
from the electrical outlet when  
not in use and before servicing.  
26.If an extension cord is  
absolutely necessary, an  
extension cord rated a  
WARNING:  
TO REDUCE  
14. Use ONLY on flat, stable  
horizontal surfaces. Do not use  
on walls, counters, windows,  
chairs or tables.  
4. DO NOT allow the appliance  
to be used as a toy. Close  
attention is necessary when  
used by or near children, pets  
or plants.  
THE RISK OF FIRE, ELECTRIC  
minimum of 15 ampere, 14  
gage cord should be used.  
Cords rated for less amperage  
may overheat. Care should be  
taken to arrange cord so that  
it cannot be pulled or tripped  
over.  
SHOCK OR INJURY READ ALL  
INSTRUCTIONS BEFORE USING  
YOUR LIGHT & EASY.  
15. DO NOT use on leather, wax  
polished furniture or floors,  
synthetic fabrics, velvet or  
other delicate, steam sensitive  
materials.  
5. Use only as described in this  
manual.  
DANGER OF SCALDING.  
Please use caution when  
6. Use only manufacturer’s  
recommended accessories.  
27.DO NOT leave unattended  
when the system is connected  
to a power supply or electrical  
outlet. Turn off all controls  
before unplugging the unit.  
using the steam mop. The steam  
16. DO NOT add cleaning  
emitted from the openings is very 7. DO NOT operate the appliance  
solutions, scented perfumes,  
oils or any other chemicals to  
the water used in this appliance  
as this may damage the unit  
or make it unsafe for use. If  
you live in a hard water area,  
we recommend using distilled  
water in your steam mop.  
with a damaged plug or cord,  
hot.  
or if the unit has been dropped,  
damaged left outdoors or  
POLARIZED PLUG:  
28 DO NOT store unit with damp  
or wet micro-fiber cleaning  
pad attached. Never leave the  
steam mop in one spot on any  
surface for any period of time  
with a damp or wet micro-fiber  
cleaning pad attached as this  
will damage your floors  
dropped into water. To avoid  
TO REDUCE THE RISK OF ELECTRIC  
the risk of electric shock, do  
not disassemble or attempt to  
repair the appliance on your  
own. Return the appliance to  
EURO-PRO Operating LLC (see  
warranty) for examination and  
repair. Incorrect re-assembly  
or repair can cause a risk of  
electrical shock or injury to  
persons when the appliance is  
used.  
SHOCK, this appliance has a  
polarized plug (one blade is wider  
than the other). As a safety  
feature, this plug will fit into a  
polarized outlet only one way. If  
the plug does not fit fully into the  
outlet, reverse the plug. If it still  
does not fit, contact a qualified  
electrician. Do not attempt to  
defeat this safety feature.  
17. When in use, NEVER turn  
the appliance over or on its  
side. NEVER DIRECT STEAM  
TOWARDS PEOPLE, ANIMALS  
OR PLANTS.  
WARNING: Your steam mop  
is designed to clean hard floor  
surfaces that will withstand  
high heat. Do not use on  
18. Carefully remove the micro-  
fiber pad immediately after you  
have unplugged and allowed  
the product to cool.  
unsealed wood or unglazed  
ceramic floors. On surfaces  
that have been treated with  
wax or some no wax floors, the  
sheen may be removed by the  
heat and steam action. It is  
always recommended to test an  
isolated area of the surface to  
be cleaned before proceeding.  
We also recommend that  
you check the use and care  
instructions from the floor  
manufacturer.  
8. To protect against a risk  
of electric shock, DO NOT  
immerse the steam mop into  
water or any other liquids.  
19. When cleaning the steam mop,  
unplug the power cord from  
the electrical outlet and clean  
with a dry or damp cloth. Do  
not pour water or use alcohol,  
benzene or paint thinner on the  
unit.  
9. DO NOT handle plug or steam  
mop with wet hands or operate  
appliance without shoes.  
10. DO NOT pull or carry by  
power cord, use power cord  
as handle, close a door on the  
power cord, or pull the power  
cord around sharp edges or  
20 To reduce the risk of fire,  
DO NOT use a flammable or  
combustible liquid to clean a  
floor.  
TOLL FREE: 1-800-418-0934  
 
S3250CW_11_IB_ENG_100913.indd 2-3  
10-09-13 10:57 AM  
Quick Start  
fig. 5  
fig. 3  
fig. 4  
fig. 1  
fig. 2  
ASSEMBLE  
FILL  
STEAM CLEANING  
4 Plug in the mop. Wait 30  
BACKSAVER  
1
Fit together the extension tubes  
as shown in the illustration.  
(fig. 1)  
3
Remove the cap to fill the  
water tank. Use the filling flask  
and funnel to fill the tank with  
water to the “MAX FILLline.  
Replace the water tank cap.  
(fig. 3)  
5
Use the Shark® Light &  
Easy™ with backsaver  
benefit to access tight  
areas. Press the release  
button on the handle  
to lock the Light &  
seconds for the unit to heat up  
and the steam to be ready.  
2
Place the micro-fiber cleaning  
pad underneath the mop head,  
with quick fastener strips facing  
up. Simply press the mop to the  
pad to attach it. (fig. 2)  
Push the handle toward the  
mop head in a pumping motion.  
Customize steam output by slow  
or fast mopping with a forward  
and backward motion. (fig. 4)  
Easy™ Steam Mop in the  
backsaver position. Press  
the release button on the  
handle again to straighten  
the handle. (fig. 5)  
TOLL FREE: 1-800-798-7398  
 
S3250CW_11_IB_ENG_100913.indd 4-5  
10-09-13 10:57 AM  
Contents  
GETTING STARTED.................................................................2  
USING YOUR STEAM MOP...................................................6  
USING YOUR ACCESSORIES...............................................9  
STORAGE AND CARE OF YOUR STEAM MOP ..........10  
TROUBLESHOOTING ............................................................12  
WARRANTY AND REGISTRATION...................................13  
Thank you for  
purchasing  
the Shark®  
Light & Easy  
Steam Mop.  
This manual covers model number:  
S3250CW 11  
TECHNICAL SPECIFICATIONS  
Voltage: 120V., 60Hz.  
Power: 1550 Watts  
Water  
Capacity: 250 ml (8 oz.)  
TOLL FREE: 1-800-798-7398  
 
S3250CW_11_IB_ENG_100913.indd 6-1  
10-09-13 10:57 AM  
English  
Getting Started  
When assembling your steam mop there  
may be a little water in or around the  
water tank. This is because we test all  
our steam mops 100% before you  
buy them, so you get a quality  
Shark® Light & EasySteam Mop.  
c
b
a
d
f
e
fig. 1  
fig. 2  
a Upper Handle Tube with Backsaver  
benefit  
ASSEMBLY  
3 Insert the assembled handle piece  
into the steam mop base. Push the  
tube base together until you hear a  
click. (fig. 2)  
IMPORTANT: Never use the Light &  
1
Remove all the parts from the  
package. Verify all the listed parts  
are included.  
Easy™ Steam Mop without attaching  
a micro-fiber cleaning pad to avoid  
damage to your floor and mop.  
b Lower Tube  
c Steam Mop Base  
d 2 All-Purpose Cleaning Pads  
e Filling Flask  
2 Slide the Upper Handle Tube (the  
tube with the handle) into the Lower  
Tube (the short tube). Push the two  
extension tubes together until you  
hear them click into place. (fig. 1)  
f Funnel  
2
TOLL FREE: 1-800-418-0934  
3
 
S3250CW_11_IB_ENG_100913.indd 2-3  
10-09-13 10:57 AM  
English  
Getting Started - cont’d  
Your micro-fiber cleaning  
pads should be replaced  
every 3 months to maximize  
cleaning performance.  
fig. 2  
fig. 3  
fig. 1  
ATTACHING THE MICRO-FIBER PAD  
Replacement micro-fiber pads are  
available at www.sharkclean.com or  
by calling 1-800-418-0934.  
FILLING THE WATER TANK  
2 A filling flask and funnel are included  
with your Light & Easy™ Steam Mop  
to make filling the water tank easy.  
Fill the flask with water and use the  
funnel to pour it into the tank. Keep  
the water level under the MAX FILL  
line. (fig. 3)  
1
Place the micro-fiber cleaning pad  
on the floor with the quick fastener  
strips facing up. Place the Light &  
Easy™ Steam Mop on the top of the  
pad to attach. (fig. 1)  
IMPORTANT: Unplug the Light &  
Easy™ Steam Mop before filling the  
water tank with water. (fig. 2)  
1
Remove the water tank cap by  
turning it counter-clockwise to the  
unlocked position. (fig. 3)  
IMPORTANT: Only add water to  
the tank. Chemicals or cleaning  
solutions may be unsafe or cause  
damage.  
3 Replace the water tank cap and turn  
it clockwise to the locked position.  
4
TOLL FREE: 1-800-418-0934  
5
 
S3250CW_11_IB_ENG_100913.indd 4-5  
10-09-13 10:57 AM  
English  
Using Your Light & Easy™ Steam Mop  
When you use your steam mop for the  
first time or if you have not used the unit  
in awhile, it may take a minute or two  
for the water to travel through the pump  
and into the heater to create steam. Get  
it started by pumping the handle a few  
times. If you have waited a few minutes  
and you still do not see any steam,  
reference the troubleshooting section  
on page 11.  
If your Light & Easy Steam  
Mop stops steaming, it could  
be out of water. Unplug the  
power cord from the electrical  
outlet and refill the water tank  
at anytime.  
fig. 1  
fig. 4  
fig. 2  
fig. 3  
fig. 5  
IMPORTANT: Your steam mop needs  
water to make steam! Never use your  
steam mop without water in the tank.  
1
Pull and twist the quick release  
cord holder to unwrap the power  
cord completely. (fig. 1) Plug into  
a 120-volt electrical outlet. (fig. 2)  
The “On” light will turn blue. If the  
light does not turn on, reference the  
troubleshooting section on page 11.  
(fig. 3)  
2 Wait 30 seconds for the boiler to  
heat the water. Pump the handle  
a few times to prime the pump,  
activate steam and moisten the  
micro-fiber pad. (fig. 4)  
3 Mop with a forward and backward  
motion to customize steam output  
automatically. (fig. 5)  
Sweep or vacuum your floors prior  
to cleaning with your Light & Easy™  
Steam Mop.  
Visit www.sharkclean.com for other  
great quick cleaning products to  
complement your Light & Easy™  
Steam Mop.  
6
TOLL FREE: 1-800-418-0934  
7
 
S3250CW_11_IB_ENG_100913.indd 6-7  
10-09-13 10:57 AM  
English  
Using Your Light & Easy™ Steam Mop - cont’d  
Care of Your Light & Easy™ Steam Mop  
fig. 1  
fig. 1  
fig.3  
fig.2  
AFTER USE AND STORAGE  
4 To store the cooled Shark® Light &  
1
When you have finished using the  
Light & Easy™ Steam Mop, unplug  
the cord from the outlet and place  
the mop into the upright position  
(fig. 1) and let the unit cool 2-3  
minutes. Release steam by pumping  
the handle several times.  
Easy™ Steam Mop, hang on a large  
hook. (fig. 3)  
1
Clean under furniture and tight  
areas using the Shark® Backsaver™  
locking handle. Press the handle  
release button and apply slight  
pressure to bend the handle. The  
Shark® Backsaver™ joint will lock at  
a perfect, access-maximizing angle.  
(fig. 1)  
NOTE: If you want to store the  
Light & Easy™ Steam Mop standing  
upright, make sure it is leaning  
against a wall for added support and  
safety. Always store your Shark®  
Light & Easy™ Steam Mop with the  
micro-fiber cleaning pad removed.  
Store away from children and high  
traffic areas.  
2 Carefully separate micro-fiber  
cleaning pad from steam mop,  
avoiding contact with the hot pocket  
or dirt. (fig. 2)  
2 Press the release button on the  
handle again to straighten.  
3 Empty the water tank before storage.  
Remove the water tank cap and  
empty the tank over a sink. Replace  
the water cap.  
8
TOLL FREE: 1-800-418-0934  
9
 
S3250CW_11_IB_ENG_100913.indd 8-9  
10-09-13 10:57 AM  
English  
Care of Your Light & Easy™ Steam Mop  
Trouble Shooting  
PROBLEM  
POSSIBLE REASONS & SOLUTIONS  
Your steam-mop should be securely plugged into a  
120V AC electrical outlet only.  
The Light & Easy™  
Steam Mop will not  
turn-on.  
Check your fuse or breaker.  
If your unit still does not work, call 1-800-418-0934.  
fig. 4  
Light & Easy™  
Steam Mop will not  
make steam.  
Is there water in the water tank? If not, add water to your  
Steam Mop following instructions on page 5.  
Light & Easy™  
Steam Mop leaves  
water on the floor.  
Is your micro-fiber cleaning pad too wet? Unplug your  
Steam Mop and change the micro-fiber cleaning pad.  
Do not leave your steam-mop on the floor with a damp or  
wet cleaning pad.  
Light & Easy™  
Steam Mop left  
white spot on the  
floor.  
Do you have hard water? If you do, you might want to  
switch to distilled water.  
Make sure the water is securely on the water tank.  
The pad might be dirty, change the pad.  
If you washed the pocket with powder detergent, then the  
pad may have residual detergent left on it. Wash it again  
with liquid detergent.  
fig. 5  
CARE OF YOUR MICRO-FIBER  
CLEANING PAD  
ORDERING REPLACEMENT PARTS  
If you are cleaning in a kitchen area where there might be a  
build-up of grease, use a de-greasing agent such as an all-  
purpose cleaner or dish soap and paper towels to clean the  
area first.  
To order additional parts and  
accessories, feel free to contact us at  
1-800-418-0934.  
Floors are cloudy,  
streaky or spotty  
after steaming.  
1
Wash pads in warm water. Wash  
separately from other laundry. Only  
use liquid detergent (no powder  
detergent). Do not use fabric  
softeners. Line dry or dry on a low  
dryer setting. (fig. 5)  
You might have left the mop in the same spot for too long.  
Do you have hard water? If you do, you might want to  
switch to distilled water.  
NOTE: Some parts may be available  
at your local retailer. Contact customer  
service for any other servicing.  
This might be leftover from past cleaners used on the floor  
surface. Use the steam mop a few more times and see if  
the leftover cloudiness is removed.  
2 If there are loose threads on the  
pad carefully cut the threads with  
scissors. Do not pull on them or cut  
at the base. (fig. 6)  
Make sure the steam pad is attached correctly.  
Light & Easy™  
Steam Mop is hard  
to push.  
IMPORTANT: The micro-fiber  
cleaning pad may be very hot  
from the steam. Use caution when  
removing. Let the unit cool for 2-3  
minutes.  
Check to see if the cleaning pad is excessively dirty.  
Replace if the pad is too dirty or wet.  
10  
TOLL FREE: 1-800-418-0934  
11  
 
S3250CW_11_IB_ENG_100913.indd 10-11  
10-09-13 10:57 AM  
English  
Notes  
ONE (1) YEAR LIMITED WARRANTY  
EURO-PRO Operating LLC warrants this product to be free from defects in material and  
workmanship for a period of one (1) year from the date of the original purchase, when utilized for  
normal household use, subject to the following conditions, exclusions and exceptions.  
If your appliance fails to operate properly while in use under normal household conditions  
within the warranty period, return the complete appliance and accessories, freight prepaid. For  
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC  
will repair or replace it free of charge. Proof of purchase date and $ 9.95 to cover the cost of  
return shipping and handling must be included. *  
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or  
replacement of the unit at our option. This warranty does not cover normal wear of parts and  
does not apply to any unit that has been tampered with or used for commercial purposes. This  
limited warranty does not cover damage caused by misuse, abuse, negligent handling or damage  
due to faulty packaging or mishandling in transit. This warranty does not cover damage or  
defects caused by or resulting from damages from shipping or repairs, service or alterations to  
the product or any of its parts, which have been performed by a repair person not authorized by  
EURO-PRO Operating LLC.  
This warranty is extended to the original purchaser of the unit and excludes all other legal and/  
or conventional warranties. The responsibility of EURO-PRO Operating LLC warranty if any,  
is limited to the specific obligations expressly assumed by it under the terms of the limited  
warranty. In no event is EURO-PRO Operating LLC liable for incidental or consequential  
damages of any nature whatsoever. Some states/provinces do not permit the exclusion or  
limitation of incidental or consequential damages, so the above may not apply to you.  
This warranty gives you specific legal rights, and you may also have other rights which vary from  
state to state or province to province.  
*Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of  
purchase date and to attach tag to item before packing with your name, complete address and  
phone number with a note giving purchase information, model number and what you believe  
is the problem with the item. We recommend you insure the package (as damage in shipping  
is not covered by your warranty). Mark the outside of your package “ATTENTION CUSTOMER  
SERVICE”. We are constantly striving to improve our products, therefore the specifications  
contained herein are subject to change without notice.  
OWNERSHIP REGISTRATION CARD FOR  
CANADIAN CONSUMERS ONLY  
Please complete and return within ten (10) days of purchase. The registration will enable  
us to contact you in the event a product defect is discovered. By returning this card you  
acknowledge to have read and understood the instructions for use, and warnings set  
forth in the accompanying instructions.  
RETURN TO: EURO-PRO Operating LLC, 4400 Bois Franc, St. Laurent, Quebec H4S 1A7  
PURCHASER: ……………………………………………………………………………………............................………............  
ADDRESS: ………………………………………………………………………………………………...........................................  
S3250CW 11  
DATE OF PURCHASE: ………………….........….. MODEL: ……………….....................................................  
NAME AND ADDRESS OF STORE: …………………………………...........................………………………………..  
12  
TOLL FREE: 1-800-418-0934  
13  
 
S3250CW_11_IB_ENG_100913.indd 12-13  
10-09-13 10:57 AM  

Sennheiser Home Security System 503125 User Manual
Shark Carpet Cleaner SC507 User Manual
Sony Camcorder Accessories GP AVT1 User Manual
Sony Portable CD Player CXS 3100 User Manual
Sony Remote Starter RM V12 User Manual
Sony Security Camera Security Camera User Manual
Sony Video Game Controller SCPH 10010 U 97026 User Manual
Southern Telecom Tablet PTAB750 User Manual
Star Manufacturing Toaster DT14 User Manual
Sun Microsystems Server 5310 NAS User Manual