Shark Vacuum Cleaner EP600 User Manual

Turbo Stick Vac  
OWNER’S MANUAL  
Models: EP600, EP600LN  
120V., 60Hz., 7.5 Amps.  
EURO-PRO Operating LLC  
94 Main Mill Street, Door 16  
Plattsburgh, NY 12901  
Tel.: 1 (800) 798-9398  
Copyright © Euro-Pro Operating LLC 2006  
 
TROUBLE SHOOTING GUIDE  
IMPORTANT SAFETY INSTRUCTIONS  
always be observed, including the following:  
When using your SHARK TURBO STICK VAC basic safety precautions should  
PROBLEM  
POSSIBLE REASON  
POSSIBLE SOLUTION  
To reduce the risk of fire, electric shock, or  
injury:  
1. Read all instructions before using your  
SHARK TURBO STICK VAC.  
2. Use the system only for its intended use.  
3. To protect against a risk of electric shock,  
do not immerse any part of the system in  
water or other liquids.  
4. Never yank cord to disconnect from outlet;  
instead, grasp plug and pull to disconnect.  
5. Do not allow cord to touch hot surfaces.  
6. Do not run appliance over cord.  
7. Do not operate the system with a damaged  
cord or plug, or if the appliance or any other  
part of the system has been dropped or  
damaged. To avoid the risk of electric  
shock, do not disassemble or attempt to  
repair the SHARK TURBO STICK VAC.  
Return the system to EURO-PRO  
1.  
2.  
Plug unit in firmly.  
Check fuse or breaker. Replace  
fuse/reset breaker.  
1.  
Power cord not firmly plugged into  
outlet.  
No power in wall outlet.  
Needs servicing.  
Do not leave the SHARK TURBO STICK  
VAC plugged in when unattended. Unplug the  
electrical cord when not in use and before  
servicing.  
VACUUM WILL  
NOT OPERATE  
2.  
3.  
4.  
3.  
4.  
Call 1-800-798-7398.  
Turn the unit off and unplug from  
outlet. Allow unit to cool down,  
then restart.  
Thermostat has tripped.  
Do not allow to be used as a toy. Close  
attention is necessary when used by or near  
children, pets or plants.  
Use only as described in this manual. Use  
only manufacturer’s recommended  
accessories.  
Do not pull cord, use cord as a handle, close  
a door on cord, or pull cord around sharp  
edges or corners. Keep cord away from  
heated surfaces.  
1.  
2.  
Empty and clean dust cup.  
Turn unit off and unplug from  
wall outlet. Remove Dust Cup  
Filter and check for object(s) in  
air duct and remove.  
Clean or replace HEPA-Type  
Filter.  
Clean debris screen.  
1.  
2.  
3.  
Dust cup is full.  
Unit clogged.  
HEPA-Type Filter needs cleaning  
or replacing.  
VACUUM WILL  
NOT PICK-UP OR  
SUCTION POWER  
IS WEAK  
3.  
4.  
4.  
Debris screen needs cleaning.  
Use only extension cords UL-rated or cUL at  
15 amperes. extension cords rated for less  
amperage may overheat. Care should be  
taken to arrange the cord so that the cord  
cannot be pulled or tripped over.  
Turn off all controls as applicable before  
unplugging from electrical outlet.  
Do not unplug by pulling on cord. To unplug,  
grasp the plug, not the cord.  
Do not handle plug or hand vacuum with wet  
hands or operate without shoes.  
Do not put any objects into openings. Do not  
use with any opening blocked. Keep free of  
dust, lint, hair and anything else that may  
reduce air flow.  
Operating LLC (see warranty) for  
DUST ESCAPING  
FROM VACUUM  
1.  
2.  
Dust cup is full.  
Dust Cup is not installed correctly.  
1.  
2.  
Empty and clean dust cup.  
Review Dust Cup instructions.  
examination and repair. Incorrect re-  
assembly or repair can cause a risk of  
electrical shock or injury to persons when  
the SHARK TURBO STICK VAC is used.  
8. Close supervision is necessary for any  
appliance being used by or near children.  
Do not leave the system unattended while  
connected.  
9. Keep hair, loose clothing, fingers and all  
parts of body away from opening and  
moving parts.  
10. Do not use to pick up flammable or  
combustible liquids such as gasoline or use  
in areas where they may be present.  
11. Do not pick up anything that is burning or  
smoking such as cigarettes, matches or hot  
ashes.  
1.  
2.  
Remove hose and/or brushes.  
Remove obstruction from hose  
and /or brush.  
VACUUM, HOSE  
OR BRUSHES  
WILL NOT PICK-UP  
1.  
2.  
Hose clogged.  
Dust cup is full.  
Empty and clean dust cup.  
ORDERING REPLACEMENT DUST CUP FILTERS  
TO ORDER REPLACEMENT HEPA-TYPE FILTERS  
Store your appliance indoors in a cool, dry  
area.  
Item # XSH600  
for Model EP600  
Call: 1 (800) 798-7398  
Keep your work area well lit.  
Do not immerse the hand vacuum into water  
or other liquids.  
12. Use extra care when cleaning on stairs.  
13. Do not use the hand vacuum without the  
HEPA-TYPE dust cup filter in place.  
14. This appliance is intended only for  
household use. Follow all user instructions  
in this manual.  
Keep end of hose, wands and other openings  
away from your face and body.  
Monday to Friday 8:30 A.M. - 5:00 P.M.  
Eastern Standard Time  
Use only on dry surfaces.  
or  
Using improper voltage may result in damage  
to the motor and possible injury to the user.  
Correct voltage is listed on rating label.  
FOR TECHNICAL SUPPORT  
for Model EP600  
WARNING: The power cord on this product contains lead, a chemical known to the  
State of California to cause birth defects or other reproductive harm. Wash hands  
after handling.  
Call: 1 (800) 798-7398  
Monday to Friday 8:30 A.M. - 5:00 P.M.  
Eastern Standard Time  
SAVE THESE INSTRUCTIONS  
Please Note:  
For Household Use Only  
The HEPA-TYPE Filter is washable. It should, however, be replaced every three (3)  
months to ensure peak performance of your vacuum.  
WARNING: To reduce the risk of electric shock, this appliance has a  
polarized plug (one blade is wider than the other). This plug will fit in a  
polarized outlet only one way. If the plug does not fit fully in the outlet,  
reverse the plug. If it still does not fit, contact a qualified electrician to install the  
proper outlet. Do not modify the plug in any way.  
Both the Pre-Motor and Post Motor Filters are washable. They should however be  
replaced every three (3) months to ensure peak performance of your vacuum.  
Important:  
Make sure that ALL filters have been completely air dried for 24 hours before re-  
installing back in the vacuum.  
Rev. 01/04A  
1
8
 
GETTING TO KNOW YOUR SHARK TURBO STICK VAC  
OPERATING INSTRUCTIONS  
Replacing The Dust Cup Into The  
Unit  
Attaching the Shoulder Strap  
Use the hooks to attach the shoulder  
strap to the vacuum cleaner.  
• Hold the dust cup in your hand.  
• Make sure that the slot on the bottom  
of the cup is pointed in the same  
direction as the pins in the unit (see  
drawing #1).  
• Slide the dust cup inside to the end of  
its place in the unit (see drawing #2).  
• Turn the dust cup 90° in the direction  
shown in the drawing (#3) at right.  
• The unit is now ready to be used  
again.  
Connect the dog leash swivel hooks  
to the eyelets located near the top of  
the unit handle and at the base of the  
unit. Adjust the strap as required for  
comfort.  
Hook for  
Shoulder  
Strap  
Hook for  
Shoulder Strap  
Warning: After extended use, the body  
of the vacuum cleaner may become hot.  
When using the unit with the shoulder  
strap, the unit will touch the body of the  
user. Therefore make sure to use the  
vacuum cleaner with the strap only when  
the unit is cool. If it gets too warm, allow it  
to cool before continuing to use it.  
Motor Thermostat  
IMPORTANT: This unit is equipped  
with a motor protective thermostat. If  
for some reason the vacuum cleaner  
should overheat, the thermostat will  
automatically turn the unit off. Should  
this occur:  
• Push the On/Off button once.  
• Disconnect the plug from the  
power source.  
• Check the source of overheating  
problem. (i.e. clogged hose or  
filter).  
• If clogged hose or filter is found,  
unclog the hose and replace the  
filters.  
• Wait at least 45 minutes before  
attempting to reuse the vacuum.  
• After unit has cooled down for  
45 minutes, plug in the cleaner  
and push the On/Off button. The  
vacuum should start again.  
• If the vacuum still does not start,  
contact customer service at  
1-800-798-7398.  
Note: To keep the vacuum cleaner  
looking new, it can be wiped with a damp  
cloth and a mild soap solution, then  
thoroughly dried. Never use any type of  
chemical cleaners as they can damage  
the vacuum cleaner. When not in use,  
store the vacuum cleaner in a dry, clean  
place.  
Technical Specifications  
Voltage:  
Power:  
120V., 60Hz.  
7.5 Amps, 900 Watts  
* Note: Illustrations may differ from actual product  
2
7
 
OPERATING INSTRUCTIONS  
PRECAUTIONARY MEASURES  
NOTE: Always turn off the power switch  
4. Reassemble the debris screen to the  
HEPA-Type filter cartridge and  
replace into dust cup (container).  
Ensure that the filter assembly is  
completely seated inside the dust cup  
(container).  
5. Attach the dust cup (container) to the  
vacuum.  
Important: Do NOT use the HEPA-  
Type filter cartridge without the debris  
screen in place.  
IMPORTANT: If the suction opening in the unit or the hose is BLOCKED, switch off  
the vacuum cleaner and remove the blocking substance before you start the unit  
again.  
and unplug the electrical cord before  
emptying the Dust Cup.  
Cleaning & Changing the HEPA-  
TYPE Dust Cup Filter  
1. Do not operate the vacuum cleaner  
too close to heaters, radiators or  
cigarette butts.  
4. When pulling out the power plug  
from the wall outlet, pull the plug not  
the power cord.  
1. After you have emptied the dust from  
the Dust Cup (container), separate  
the debris screen from the HEPA-  
Type filter cartridge by grasping the  
debris screen with one hand and the  
filter frame with the other and pull  
apart.  
PLEASE NOTE: The white pleated  
filter material in the HEPA-TYPE Filter  
will discolor over time -This is  
NORMAL and will NOT affect the  
performance of the filter. If the HEPA-  
TYPE Filter  
5. Do not pick up anything that is  
burning or smoking such as  
2. Before inserting the power plug into  
the wall outlet, make sure that your  
hands are dry.  
cigarettes, matches or hot ashes.  
Fig. A  
is properly  
Debris Screen  
HEPA-TYPE  
Filter  
cleaned  
Wash  
once a  
month or  
when  
suction  
appears  
reduced  
after each use  
and suction  
2. Rinse the debris screen under the  
faucet until clean. Allow to air dry or  
dry with a clean dish towel. Do NOT  
wash in dishwasher.  
3. To clean the HEPA filter cartridge,  
hold filter by frame flange and tap  
filter on the inside wall of a dust  
container (garbage can).  
does not return  
to 100%, then  
we suggest that  
the HEPA-TYPE  
Filter be cleaned  
vigorously until  
no more dust  
6. Do not use without dust cup filter in  
place.  
Warning: Allow 24  
hours for drying before  
replacing in unit.  
3. Before you start vacuuming, make  
sure to remove large or sharp objects  
that might damage the dust cup filter.  
can be removed,  
then rinsed under the faucet and  
allowed to air dry for 24 hours before  
replacing into the vacuum. (Fig. A)  
This should be done once a month  
or when suction appears to be  
reduced .  
NOTE: If you wash the HEPA-TYPE  
filter, make sure that it has  
completely air dried for 24 hours  
before inserting back in the  
vacuum.  
Ensure that you do not damage the  
pleated filter material during cleaning.  
Also note that discoloration occurs  
during use. This does NOT affect the  
filter’s performance.  
Warning: Always empty the dust cup and clean the HEPA-Type dust cup  
before each use and during prolonged usage. Never over fill the dust cup -  
remove dirt and clean the HEPA-Type dust cup filter during prolonged usage or risk  
motor damage. Make sure that the debris screen and the HEPA-TYPE filter  
have completely air dried before replacing into the vacuum.  
6
3
 
OPERATING INSTRUCTIONS  
OPERATING INSTRUCTIONS  
Crevice Tool  
For radiators, crevices, corners,  
baseboards and  
WINDING & UNWINDING THE  
POWER CORD  
• To wind the cord  
after usage, follow  
the illustration below.  
• To unwind the power  
cord, follow the  
illustration below  
but in the opposite  
direction.  
NOTE: Always remove the power plug  
from the wall outlet before assembling or  
removing accessories.  
ATTACHING THE HOSE TO THE  
MAIN BODY  
• Press in the pin at the end of the  
hose (see illustration below).  
• Insert the hose into its place (see  
arrow in illustration).  
between cushions.  
INSERTING THE 2-PIECE METAL  
HANDLE INTO THE MAIN BODY  
Dusting Brush  
The dusting brush is used for the  
furniture, venetian blinds,  
books, lamp shades  
and shelves.  
• Push in the pin at the end of the lower  
piece of the metal handle (see  
illustration).  
• Insert the metal handle into the hole  
next to the handle. Make sure that the  
slot in the handle fits correctly into the  
opening. (See illustration.)  
• When inserted correctly, the pin will  
show in the pin hole.  
• When using the vacuum, attach the  
cord to the cord holder so that the  
cord is out of the way when you are  
vacuuming. (See below.)  
Emptying The Dust Cup  
• When inserted correctly, the pin should  
rest in its hole.  
Pin Hole  
Warning: Always unplug the unit from  
electrical outlet before opening the Dust  
Cup (container).  
Top of Retractable Handle  
• Hold the dust cup in your hand.  
• Turn it a complete 90° in the direction  
shown in drawing #1. (Turning less than  
90° will cause the dust cup to be  
attached on its bottom.)  
• Let the dust cup come down slightly as  
shown in drawing #2.  
Pin  
Cord Holder  
Pin  
Hole  
• Slide the dust cup out towards you (see  
arrow in drawing #3).  
• Hold the dust cup in your hand and  
remove the HEPA-Type dust cup filter  
(see drawing #4).  
USING THE UNIT AS AN UPRIGHT  
• Unwind the power cord and plug into  
the 120V outlet.  
• Push down in the direction of the arrow  
to obtain best results on carpets or on  
hard wood floors.  
ON/OFF SWITCH  
• The On/Off switch has two different  
positions.  
• Push on the "I" side to turn the  
vacuum ON.  
• Push on the "O" side to turn the  
vacuum OFF.  
• To insert the upper piece of the metal  
handle, press on the pin that is on the  
upper handle and insert into the lower  
handle making sure that the pin comes  
out of the pinhole on the lower handle.  
• Empty the dust cup (see drawing #5).  
NOTE: When vacuuming  
deep pile carpets or  
hard to vacuum  
carpets, lower the  
angle of the 2-piece  
metal handle  
(see illustration at  
below) for  
easier  
ATTACHING THE FLOOR BRUSH  
TO THE MAIN BODY  
= OFF  
= ON  
• Push in the pin in the floor attachment  
as shown in the illustration at right.  
• Insert the floor brush into its location,  
in the direction  
of the arrow.  
• When inserted  
correctly, the  
pin will show in  
the pin hole.  
maneuverability.  
USING THE UNIT AS A HAND  
VACUUM  
• Disconnect the metal handle.  
(See page 4.)  
• Disconnect the floor brush.  
(See page 4.)  
4
Pin  
Hole  
• Attach the hose. (See page 4.)  
• Attach the crevice tool or the dusting  
brush. (See below.)  
• Attach the shoulder strap.  
(See page 7.)  
5
5
4
 

Shark Vacuum Cleaner EP045 User Manual
Shop Vac Vacuum Cleaner 87L350 User Manual
Sony Cell Phone D6502 User Manual
Sony Computer Drive NW HD3 User Manual
Sony MP3 Player CFD F10 User Manual
Sony Stereo System CMT DV2D User Manual
Sony TV Mount SLR 104 User Manual
Sony Universal Remote RM VL700 User Manual
SpectraLink Cordless Telephone e340 h340 i640 User Manual
Sungale Digital Photo Frame CD500A User Manual