Stanton Turntable STR8 30 User Manual

FULL MANUAL  
DIRECT DRIVE TURNTABLE  
STR8-30  
WARNING : TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT  
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.  
 
AS S EMBLY  
1. Remove the main unit with the packing from the box  
and take off the packing.  
2. Insert the turntable platter onto the center spindle.  
3. Set the slip mat on the platter.  
of the tonearm.  
7. Adjustment of horizontal zero (0) balance and  
stylus pressure:  
(a) Remove the stylus protector, do not touch the  
stylus tip during the adjustment.  
4. Installation of cartridge:  
When installing a cartridge, refer to the operating  
instructions of that cartridge.  
(d) Release the arm clamp and lift the tonearm  
from the arm rest to free it.  
During installation, attach the stylus protector to  
guard the stylus tip from damage.  
(1) Connect the lead wires to the cartridge terminals.  
The terminals of most cartridges are color coded.  
Connect each lead wire to the terminal of the  
same color.  
(c) Rotate the counterweight until the tonearm is  
approximately balanced horizontally (floats  
freely).  
(d) Refasten the tonearm with the arm clamp.  
(e) Hold the counterweight stationary with one  
hand and rotate only the stylus-pressure ring  
to bring the number "0" of the ring into  
alignment with the center line on the tonearm  
rear shaft.  
(f) Rotate the counterweight clockwise until the  
scale shows the value corresponding to the  
pressure of the used stylus. The average stylus  
pressure of the cartridge body is 1.5-2 g. If  
you use a non-Stanton cartridge, please follow  
that manufacturer’s instructions.  
White  
Blue  
Red  
(L+) .…....………….... Left channel+  
(L-)....………............... Left channel-  
(R+) ……....….......... Right channel+  
(R-) .………..…......... Right channel-  
Green  
(2) Install the cartridge to the headshell and tighten  
it with screws provided with the cartridge.  
5. Insert the headshell into the front end of the  
tonearm, then turn the lock nut clockwise with the  
headshell firmly held horizontally.  
6. Slide counterweight onto tonearm.  
8. Install the dust cover to the main unit.  
Twist it lightly and it will screw onto the rear shaft  
P LACEMENT  
or through the air resulting in feedback. Find a  
location which is very stable and vibration free.  
The legs have functions for adjusting the height of  
the unit itself. Adjust the legs to stabilize the main  
body horizontally.  
Do not place the unit in a location where it will be  
exposed to direct sunlight or near a heating appliance.  
Do not place the unit in a location where there is high  
humidity or a lot of dust.  
Cartridge may pick up slight sound pressures or  
vibrations from the speakers coming along the floor  
CONNECTIONS  
1. Connect the power cord to the auxiliary power outlet  
on the rear panel of your amplifier or receiver or to a  
household AC outlet.  
NOTE:  
Be sure to connect the ground terminal firmly to the  
amplifier or receiver.  
2. Connect the unit output terminals to the PHONO  
jack of your amplifier or receiver.  
If this connection is not made or is loose, a power  
source "HUM" will result.  
Output terminals  
L (White)  
R (Red)  
Amplifier(Receiver)  
L Channel  
>>  
>>  
>>  
R Channel  
GND  
GND (Spade)  
 
OP ERATION  
1. Rotate the power dial clockwise to turn on the  
power, the speed indicator and the strobe-  
illuminator will light up.  
2. Place a record on the slip mat, when playing a  
45rpm record with a large center hole, place the  
45-rpm adaptor on the center spindle.  
5. Press the Start/Stop button, the turntable platter  
will start to rotate.  
6. Move the tonearm over the desired groove.  
7. When play is finished, move the tonearm to the  
arm rest, secure the tonearm with the arm clamp.  
8. Press the Start/Stop button to stop the platter  
rotating, push the power button to turn off the  
power.  
3. Set the speed to match the record.  
4. Remove the stylus protector, release the arm clamp.  
MAINTENANCE  
For best results & proper care of your equipment use  
Stanton Vinyl Cleaner (VC-1) for your records and  
Stylus Cleaner Kit for styli (SC-4).  
Clean the stylus periodically with a soft brush to  
prevent the accumulation of dust.  
From time to time, the dust cover and turntable  
cabinet should be wiped with a soft and dry cloth.  
Any volatile materials such as alcohol, thinner,  
benzine, etc., may remove the paint or damage the  
lustre, please avoid.  
When the sound becomes distorted or noisy, check  
the stylus. If worn out, replace it with a new one.  
S P ECIFICATIONS  
*General  
Power supply..…...………...AC 115/230V~, 50/60Hz  
Power consumption..........................................9 Watts  
Dimension(WxDxH).........….......450 x 350 x 140 mm  
Weight..................................................…........4.6 Kgs  
For improvement purposes, specifications and design may be changed without notice.  
502-STR830-1213  
 

Sennheiser Power Supply ADN PS User Manual
Sony CD Player CDX 646X User Manual
Sony DVR DVW 2000P User Manual
Sony Stereo System TC WE675 User Manual
State Industries Water Heater SRGSS00905 User Manual
Sunbeam Microwave Oven SBMW1109W BL User Manual
Sunbeam Microwave Oven SGA9901 User Manual
Superior Indoor Fireplace CST38MH User Manual
Swisher Lawn Mower T1360 User Manual
Sylvania CRT Television 6427TF User Manual